XRay

Xray Low Friction Kevlar Belt for T4'20

This is a pack of ten replacement XRAY 3mm Locknuts. These nuts feature an inner nylon ring for a secure hold.

This is a pack of ten replacement XRAY 3x10mm Set Screws, and are intended for use with the XRAY T2 009, T3, T3R and T3'12 1/10 touring cars, as we...

Xray M3x18 Hex Screw 903318

This is a set of replacement servo arms for the Xray XB8 line of buggies. This set of molded composite servo arms includes double-arm for throttle ...

This is a set of two replacement front suspension pivot pins for the XRAY T2 1/10th scale touring car. Lower outer pivot pins. Hardened for very hi...

This is a pack of two optional XRAY Black 1.2 Rate Side Springs. These springs are harder than the stock Gold springs.

This is a replacement XRAY Rear Drive Axle, and is intended for use with the XRAY XB4 1/10 4wd buggy. Package includes one rear axle.

The springs have been specifically designed to complement the big bore shocks. Set of 2. The spring rate of the linear springs is constant during t...

Silicone O-ring fits over 3mm shaft. 2mm thick. Set of 10 pieces

Xray Silicone O-Ring 3x2.1 (10)

Silicone O-ring fits over 5mm shaft. 2mm thick. Set of 10 pieces.

Silicone O-ring fits over 6mm shaft. 1.55mm thick. Set of 10.

**** 1.5mm chassis requires special low profile screws for installation, #913300. Standard countersunk screws will not fit and may cause damage to...

XRAY XB2 Stainless Steel Battery Weight was developed to be placed beneath battery to add weight as low as possible. This helps to make the car eas...

This is a pack of two replacement XRAY Long Steel Steering Bushings, and are intended for use with the XRAY XB4 1/10 scale 4WD buggy. These bushing...

Long Bushings:   Precision-machined long bushing for front C-hub steering block pivot screws. Set of 2.   Short bushings:   Precision-machined shor...

This is a replacement XRAY 4S Spring Set C, and is intended for use with the XRAY T4 1/10 scale electric touring car. These springs can be used on ...

XRAY T4 2019 Aluminum Chassis Stiffener. CNC-machined chassis stiffener made from premium 2.0mm Swiss 7075 T6 aluminum. The front brace – which can...

Alu Shim 3X6X1.0MM - Orange or Black (10pcs)

This is a pack of two optional XRAY Aluminum Solid Axle Driveshaft Adapters, and are intended for use with the XRAY T2 008 EU and US, T2 009 EU and...

New T4 ECS BB DRIVE SHAFT – SET Ball-bearing equipped ECS drive shafts Reduced friction between driveshaft and outdrive Ball-bearings replace comp...

This is an optional Kevlar front drive belt for the XRAY T2 1/10th scale touring car. Ultra-Flex High-Performance Drive Belt For top competition ra...

This is an optional XRAY Brass Battery Backstop. The stylish optional CNC-machined battery backstop made from brass material is used as a backstop ...

Composite Ball Joint 4.9MM - Closed With Hole (4)

Molded-composite diff drive shaft adapters for #305184/305188 XRAY Composite Solid Axle. Modular design with composite output shafts allows for eas...

Composite Steering Block - Graphite - V2

Composite Steering Block - Hard - V2

Composite Steering Block - Medium - V2

Diff Gasket (4)

Low friction 3.5mm drive pin clips for protection and cushioning of drive shaft pin in diff outdrives. Set of 4. For use only with XRAY T2'008 alu ...

Eccentric bushings for adjusting suspension settings, made from tough composite. Fits XB4 alu suspension holders. Using eccentric suspension bushin...

Front body mount set includes redesigned 6mm-thick bodyposts and all other mounting hardware. Fits XRAY T2 and NT1. Update: Composite brace for bu...

This is a replacement XRAY Composite Bumper Lower Brace Set, and is intended for use with the XRAY T4 1/10 scale electric touring car. Bumper brace...

Xray T4 Front Sway Bar

Xray T4 Graphite Body Upstop 2mm (2)

XRAY T4 High-Performance Low Friction Kevlar Drive Belt Rear 3 X 189 MM 305447

Molded composite 4.9mm ball joints, open on both sides, for connection to 4.9mm ball. Set of eight. Fits XRAY T2, T3.

Molded-composite rear upright features built-in 0° of outboard toe to improve traction and prevent suspension geometry changes in serious crashes. ...

This is a replacement XRAY 3x189mm High-Performance Kevlar Rear Drive Belt, and is intended for use with the XRAY T2R Pro and T2 009. This speciall...

Rear body mount set includes redesigned 6mm-thick bodyposts and all other mounting hardware. Fits XRAY T2 and NT1.

Rear Suspension Arm - Graphite - 1-Hole

This is an optional XRAY Spring Steel Solid Axle Driveshaft Adapter Set, and is intended for use with the XRAY T2 and T3 family of vehicles equippe...

This is a set of four replacement steel steering bushings for the XRAY T2 1/10th scale touring car. Bushings are precision machined and are used fo...

Lower inner pivot pins for XRAY T4’14. Hardened for extra-high durability and long life. Set of 2.